By Thaniell - 16 maja 2016, 09:40
Posty: 5564
Rejestracja: 14 maja 2010, 17:34
Posty: 5564
Rejestracja: 14 maja 2010, 17:34
Thaniell pisze:No to fakt, ale zawsze już bliżej, niż dalej
+++Kayfun 5 - Erste Schritte TEIL 1/2+++
Wer gut schmiert, der gut fährt!
Die ersten Kayfun 5 sind auf dem Weg zu euch. Damit die ersten Schritte gut gelingen, hier ein paar Infos:
1. Bitte schmiert die O-Ringe der Liquid Control vor der ersten Verwendung. Dies erleichtert die Bedienung und verhindert, dass die Liquid Control sich eventuell verklemmt.
2. WICHTIG: Im Ersatzteil Tütchen sind 2 Paar Wicklungsschrauben enthalten: Einmal ganz normale und einmal etwas längere. Letztere sind nur für SEHR DICKE DRÄHTE geeignet. Sie lassen sich nicht vollständig in die Base hineinschrauben. Wer das trotzdem mit Gewalt versucht, könnte diese eventuell abbrechen, was die Base des Kayfun 5 unbrauchbar machen kann.
3. Der Kayfun 5 bietet eine Vielzahl von Möglichkeiten, wie ihr die Wicklung befestigen könnt.
Krasnal45 pisze:Taa, tylko ciekawe, kto łapie dripa samymi koniuszkami ust...
Thaniell pisze:Pany, to jest temat o Kayfun 5, a nie rurkach srurkach i innych wynalazkach.
@LICHU, nie rób burdelu, tylko załóż sobie temat w odpowiednim dziale.
Wracając do tematu to bardzo mnie ciekawi cug, czy faktycznie będzie tak działał jak na filmie. Chodzi mi czy faktycznie odwzorowali przeciąg taki jak był we wcześniejszych wersjach.
Small/ medium sized coils
For regular sized coils (length ~5mm) the easiest way to place and mount them is:
unscrew the build screws until they reach over the building hooks.
place your leads on each side between build screw and building hook.
screw down the build screws do fixate the wire.
clip your leads so that they don’t stick out over the rebuilding platform.
slightly lift up your coil to make sure it isn’t touching any steel part.
Medium sized/ large coils
For larger coils, you can also:
unscrew the build screws until they have the same height as the rebuilding hooks
wrap your leads around the rebuilding hooks on each side
screw down the build screws do fixate the wire.
clip your leads so that they don’t stick out over the rebuilding platform.
slightly lift up your coil to make sure it isn’t touching any steel part.
Oversized coils
unscrew the build screws until they have the same height as the rebuilding hooks
wrap your leads around the rebuilding hooks on each side
screw down the build screws do fixate the wire.
clip your leads so that they don’t stick out over the rebuilding platform.
slightly lift up your coil to make sure it isn’t touching any steel part.
Please notice that the Kayfun 5 has two pairs of build screws included in the spare kit.
The longer set is for builds with very thick wires only. These screws cannot be screwed into the base completely! Forcing them beyond the threading may cause them to break off and eventually leaving the base of the Kayfun 5 unusable.
Please be aware that the rebuilding space is not endless. In case your build exceeds a diameter of 5mm and/ or a width of 9mm it may touch the evaporation chamber, when the liquid control is closed, which causes a short circuit
Example:
distance of the coil from the air outlet: 2mm
inner diameter: 3mm
wire size: 1mm
total size of the coil: 5mm
Wer in seinem Leben schon mal einen Kayfun gewickelt hat, weiß vermutlich sofort wie das Wickeln beim Kayfun 5 funktioniert. Nichts desto trotz bietet der Kayfun 5 eine Vielzahl an Befestigungsmöglichkeiten für unterschiedliche Coils, sowie ein paar Details auf die zu achten ist:
1. Kleine Coils:
-schraube die Wicklungsschraube heraus, bis diese über die Wicklungshaken ragt.
-Lege das Drahtende auf jeder Seite zwischen Wicklungsschraube und -haken
-Fixiere den Draht mit der Wicklungsschraube
-Schneide das Drahtende bündig zur Schraube ab
-Hebe die Wicklung leicht an, sodass sie keine Stahlteile berührt
2. Mittelgroße Coils:
-schraube die Wicklungsschraube mindestens soweit heraus, dass sie auf derselben Höhe wie die Wicklungshaken ist.
-führe das Drahtende auf jeder Seite um beide Wicklungshaken herum
-Fixiere den Draht mit der Wicklungsschraube
-Schneide das Drahtende bündig zur Schraube ab
-Hebe die Wicklung leicht an, sodass sie keine Stahlteile berührt
3. ACHTUNG bei sehr großen Coils
-für dickere Drähte liegen extra lange Wicklungsschrauben im Ersatzteiltütchen bei.
-diese können nicht vollständig in die Base geschraubt werden!
-Clapton Coils und dergleichen sollten einen Außendurchmesser von 5mm und eine Breite von 9mm nicht überschreiten, sonst droht ein Kurzschluss!
Siema, Mam dość irytujący problem z OXVA slim pro[…]